Coralife Power Center

Never again "rig-up" multiple timers and power strips to run heating, lighting, humidifiers, and accessories on your reptile's home. Easy-to-use Power Center means clutter-free custom illumination. Combines 24-hour timer(s) and 8-outlet indoor power strip for seamless transition from dawn to dusk lighting conditions. Single has 4 timer-controlled (2 daytime/2 nighttime) and 4 constant-power outlets while Dual has 7 timer-controlled (3 daytime, 2 actinic, and 2 lunar lights) and 1 constant-power outlet to sequence daylight, actinic, and lunar lights for the ultimate lighting system. Single Digital Power Center has 4 constant-power outlets and 4 alternating timer-controlled outlets (2 daytime/2 nighttime). Enhanced digital feature allows alternating timer to set the day-night cycle at different times of the day at different days of the week.

Features: Sliding safety covers. 3 ft power cord with grounded plug. 15 amp, 120 volt (1875 watt max); UL-Listed. Single and Single Digital 2-7/8" x 10-1/2" x 1-1/8" high. Dual 3" x 13" x 1-1/2" high.

Push up timer-tabs (located at the edges of the timer-dial) toward the center of the dial to turn yellow outlets on and blue outlets off. Push the timer-tabs down to turn blue outlets on and yellow outlets off. Each timer-tab represents a 15-minute interval. The white outlets provide constant power controlled by the on/off switch. The on/off switch controls power to all outlets and the timer.

Setting the Timer:

1. Turn the manual control switch to the timer "ON" position.
2. Set the current time of day by turning the timer-dial clockwise until the correct time faces the arrowhead.
3. Set the times that you want the yellow and blue outlets to turn on and off by using the timer-tabs.

Bypass the timer by using the manual control switch. To activate the yellow outlets continuously, turn the switch to the yellow "ON" position. To activate the blue outlets continuously, turn the switch to the blue "ON" position.

1. Turn the manual control switch to the timer "ON" position. Set the timer to the current time of day.
2. Pick the time of day you want the daytime lights turned on and push timer-tabs up to turn on yellow outlets for daytime applications.
3. Continue pushing the timer-tabs up until you reach the time of day that you want the daytime lights turned off.
4. When the daytime timer is set, the nighttime timer is automatically set by leaving the remaining timer-tabs down to turn on the blue outlet.

Warning:
Designed for indoor use only. This device should not be installed in wet or damp areas. If installed in a wet or damp area, this device must be plugged into a receptacle controlled by a GFCI (ground fault circuit interrupter) breaker. Device must be properly connected to a grounded three-prong receptacle.

Time Setting Instruction for the Dual Power Center

Alternating Timer Instructions:

1. Turn the manual control switch to the timer "ON" position. Set the timer to the current time of day.
2. To set the time for when the Actinic Blue/nocturnal outlets (actinic cycle) will turn on, the timer tabs must be in the down position at the desired starting time.
3. Continue around the timer dial in the sequential order (verifying that all the tabs in the actinic cycle are in the down position) until reaching the end of the cycle where the Actinic Blue/nocturnal outlets will be turned off.
4. Push up the timer tabs at the end of the desired actinic/nocturnal cycle to turn on the Lunar Light outlets.
5. Continue pushing the tabs up until reaching the starting time of the actinic/nocturnal cycle.

Note: Daylight and nocturnal outlets alternate power. Both outlets cannot be on at the same time (i.e. when nocturnal outlets are on, the daylight outlets are off).

Day-shift Timer Instructions

1. Turn the manual control switch to timer "ON" position. Set the timer to the current time of day.
2. To set the timer for when the daylight outlets day-shift cycle will turn on, the timer tabs must be in the down position at the desired starting time.
3. Continue around the timer dial in the sequential order (verifying that all the tabs in the day-shift cycle are in the down position) until reaching the end of the cycle where the daylight outlets will be turned off.
4. Push up the timer tabs at the end of the desired day-shift cycle to turn off the daylight outlets.
5. Continue pushing the tabs up until reaching the starting time of the day-shift cycle.

Note: Each timer tab represents a 15-minute interval.