World-renowned aquarium pump boasts exceptional quality and reliable performance. Epoxy filled, hermetically sealed, low energy consumption motors result in silent, efficient operation while surpassing the highest safety standards. Features removable integrated pre-filter for convenient installation. Run internally or externally in fresh or saltwater. Barb I/O fittings with built-in twist clamp.
Metric Conversion
9/12mm = 3/8"
12/16mm = 1/2"
16/22mm = 5/8"
25/34mm = 1"
1046 Hobby Pump
80 gph with a maximum head of 4 feet at only 5 watts. Input 12/16 mm, output 9/12 mm.
1048 Hobby Pump
160 gph with a max head of 5 feet at 10 watts. Input 12/16 mm, output 12/16 mm.
1250 Hobby Pump
320 gph with a max head of 6.5 feet at 28 watts. Input 16/22 mm, output 12/16 mm.
1260 Hobby Pump
634 gph with a max head of 12.1 feet at 65 watts. Input 25/34 mm, output 16/22 mm.
1262 Hobby Pump
898 gph with a max head of 11.8 feet at 80 watts. Input 25/34 mm, output 16/22 mm.
Please click on "More Information" for further details.
Using an in-line pump with a wet/dry filtration system: Water flows via gravity from the aquarium into the wet/dry filter, and then into the filter's sump. From the sump, it flows into the pump via gravity through a bulkhead installed in the side of the sump. The pump sends water back up into aquarium from the wet/dry filter's sump. When installing pumps with wet/dry filtration, you'll need to drill into the filter's sump to install the bulkhead, then mount the pump level to the bottom of the filter's sump.
Using an in-line pump with canister filtration: Water moves via gravity from the aquarium into the pump. The pump pushes the water through the canister filters, and back up into the aquarium (or UV filter, chiller, etc.). You need to siphon water from the aquarium and flood the pump before turning it on.
Never restrict the inlet flow of any water pump. This will quickly cause permanent motor damage.
You can restrict the outlet flow of the water pump with a ball valve in order to achieve the desired flow rate.
Use ball valves before inlet and after outlet to make pump removal easy and spill free.
Anytime a threaded connection is used, be sure to use Teflon tape. When using barb insert connections to flexible tubing, use hose clamps. (Plastic hose clamps are required for underwater use.)
Submerged Pump:
Set your submersible pump on suction cups at the bottom of your sump. This will help reduce vibration and noise.
Be sure to completely submerge the pump before connecting it to a power source.
Try not to place the submerged pump's inlet near the output of the protein skimmer, if you have one installed. A skimmer can sometimes produce air bubbles in the exhaust water, and these bubbles can be sucked up by the pump and returned to the aquarium. These bubbles are undesirable inside an aquarium, especially a reef aquarium.
Remove filter from the front of submerged pumps and remove debris. Rinse with plain fresh water (no soap).
Remove the impeller housing cover to expose the impeller.
Remove the impeller and the magnet. Inspect them for damage and wash with plain fresh water (no soap or abrasives).
Wash out the impeller housing with plain fresh water (no soap or abrasives).
Reassemble the pump and re-install it in your system.
Other Cleaning Tips:
Some brands of in-line pumps require periodic oiling to lubricate the motor. Always refer to your owner's manual for instructions on this procedure.
If you have lime or mineral buildup on any part of your pump, you can dissolve these with Lime Off, which is especially designed for removing lime, salt residue, and other hard deposits on aquarium equipment. Make sure to rinse thoroughly with fresh clean water before reassembling your pump.
I purchased my first Eheim 1060 11 years ago. I installed it on my Oceanic Reef Ready 75 tank with an Oceanic Wet Dry filter. It's been running non-stop for the past 11 years and is still running flawlessly today.
I pulled the pump for a quarterly cleaning and as always, no wear was evident at all on the impeller or the ceramic shaft.
I bought a 1260 over 3 years ago and it has been running flawlessly. It is so quiet that you cannot hear it over the fans of my lights or the running water. It may be more expensive and it may not be the most efficient pump but when something is that quiet and reliable, you have to ask yourself does it really matter? Seriously, buy the pump!
A proper flow rate is essential for your aquarium's filter to work its best. This means that your aquarium will stay cleaner longer, providing a healthier environment for your inhabitants.
When choosing a water pump type and size, there are several factors to include in your decision. Filtration type, desired flow rate, plumbing and head height, and adding additional devices all come into play. This article helps clear the confusion.
Your primary objective is to maintain a healthy thriving aquatic environment for your underwater plants and animals. To achieve this goal, one of the most critical decisions you'll make is choosing the right pump. Compare pumps here.
The primary role of water pumps is to move water to or from the filtration systems in freshwater or saltwater aquariums. There are two main types of setups. This article discusses both.
Please note: Return of electrical equipment to Drs. Foster & Smith for exchange or refund is limited to 60 days from the date of purchase. Beyond 60 days, please contact the manufacturer for repair or replacement as covered by the manufacturer's warranty.
 "Eheim Hobby Pumps")
World-renowned aquarium pump boasts exceptional quality and reliable performance. Epoxy filled, hermetically sealed, low energy consumption motors result in silent, efficient operation while surpassing the highest safety standards. Features removable integrated pre-filter for convenient installation. Run internally or externally in fresh or saltwater. Barb I/O fittings with built-in twist clamp.
